Fridge repair in Ruaka.
Fridge and freezer repair at your home in Ruaka, Kiambu, including Ndenderu, Banana, Muchatha and Two Rivers. Price agreed before any work starts.
Homes, shops and offices.
We repair home fridges, chest freezers and shop coolers in Ruaka and nearby Ndenderu and Banana. Tell us what the fridge is doing and where you are, and we give you the earliest time a technician can reach you.
Most jobs are done in one visit. If a part has to be ordered, we tell you the price and how long it takes before we leave.
Homes and businesses we visit.
Ruaka is one of the fastest-growing corridors around Nairobi, with new apartment blocks, shopping centres and family homes. Kitchens in new apartments are often compact, so the fridge sits tight against a wall or inside a cabinet.
Apartment blocks share one power supply, so a surge or a dip reaches every fridge in the building at once. That is why several neighbours sometimes call us on the same day.
Ruaka is a busy growth corridor with new apartments, shops and family homes. Many kitchens here are small, so fridges are often pushed tight to the wall, and the cold air cannot escape from the back.
We cover Ruaka and nearby Ndenderu, Banana, Muchatha and Two Rivers. For a fridge that is not cooling in this area, we check the spacing and the condenser before we look at gas.
What goes wrong here.
Fridge pushed against the wall
Condenser heat has to leave the back of the cabinet. With no gap, the heat stays trapped, the compressor runs longer and the cooling weakens. Pulling the fridge out and giving it room often helps immediately.
Board damage after a surge
Inverter boards are sensitive to voltage spikes. A fridge that is dead, blinking or starting and stopping after a power event needs the board, the relay and the compressor tested one by one.
Ice build-up in no-frost fridges
Ice on the back wall of the freezer means the defrost system is not clearing frost. The heater, the sensor or the timer is the usual cause, and each is tested before anything is replaced.
Water under the drawers
A blocked defrost drain lets melted frost spill into the fridge. On dispenser fridges, a loose line can do the same. We find where the water starts before choosing the repair.
Care for Ruaka kitchens.
Leave a hand-width gap, clean the coil every few months, and use a voltage guard. In an apartment block these simple steps protect the fridge from most of what goes wrong.
Newer fridges in Ruaka are almost always worth repairing. We show you the diagnosis and the cost before any part is changed.
What we fix.
Brand-specific repair in Ruaka.
If you know the brand, go straight to the page for that brand in Ruaka. The usual faults and how we fix each one, written for your model.
How a Ruaka visit works.
Tell us what is wrong
Call or WhatsApp with what the fridge is doing and a photo of the model sticker inside.
We come to you
A technician visits your home or business and finds the fault.
You approve the price
You get the full price before any work starts. Nothing is done without your OK.
Cold again
We repair it, test the temperature and show you what was fixed.
Good to know about your fridge.
Cleaning the condenser coil
The condenser coil releases the heat the fridge removes from the food. On older fridges it is a grille on the back; on newer ones it may be a coil under the fridge behind a kick plate. Dust and kitchen grease form a blanket on it, which traps the heat.
Unplug the fridge before you start. Use a soft brush or the brush attachment of a vacuum cleaner to lift the dust, then a damp cloth for grease. Clean the area around the compressor too, and remove dust from the fan if there is one. Do it every few months, or more often in a dusty kitchen.
A clean coil can make a noticeable difference in how long the compressor runs and how much power the fridge uses. It is one of the cheapest and most effective bits of maintenance you can do yourself.
How to tell if a door seal needs replacing
The door seal, or gasket, keeps warm air out. Over time it hardens, cracks or loses its magnetic grip. A bad seal causes frost, water inside, longer running and a higher bill.
Try the paper test: close the door on a sheet of paper and pull it out. If it slides out with no resistance, the seal is not gripping there. Test several points around the door. Look for splits, hardened sections and mould along the folds.
Wiping the seal with warm soapy water sometimes restores the grip, because grease and sugar stop it sealing. If cleaning does not help, the seal needs replacing. A new seal must be fitted straight, and the door adjusted so it closes evenly, or the new seal will not fix the problem.
Choosing a fridge technician you can trust
A good technician explains the fault before changing parts. They test, tell you what failed and why, and give you the price before work starts. They show you the old part if you ask. They are honest when a repair does not make sense.
Be wary of anyone who names a fault over the phone without seeing the fridge, who insists on a gas refill without finding a leak or who will not give a price until the work is done. Ask whether the visit fee is separate and what it covers.
It also helps if the technician works on fridges every day. Fridges are a sealed cooling system with their own tools, gases and habits, and a general handyman may not have the equipment to vacuum and charge a system properly.
Moving a fridge without damaging it
Whenever possible, keep a fridge upright. The compressor oil sits in a defined place, and laying the fridge down can let it run into the pipes. If a fridge has to travel on its side, let it stand upright for several hours before you switch it on again.
Empty it and defrost the freezer the day before, so no water leaks on the way out. Secure the doors with tape and protect the corners. Plan the route, because large fridges are heavy and awkward on stairs, so tell your movers the size and the floor.
Level the fridge in its new position, leave a gap behind and above it and wait a short time before switching it on. We also help with installation and relocation, including bringing in a new fridge and removing the old one.
Saving power with the fridge you already have
A fridge runs all day and every day, so small improvements add up. Set the fridge between about three and five degrees and the freezer at minus eighteen. Colder settings use more power without protecting the food any better.
Keep the condenser clean, leave air space around the fridge and keep it away from the cooker and direct sun. Check the door seal and do not leave the door open while you decide what to eat.
A full fridge holds its cold better than an empty one, so a few bottles of water on the shelves help in a fridge that is mostly empty. Do not overpack it, though, because the air must still move. If a fridge is very old and the compressor is struggling, a replacement may repay itself in power, and we will tell you honestly if that applies.
Inverter fridges explained
A traditional compressor switches fully on and fully off. An inverter compressor changes its speed to suit the cooling needed. It runs slowly most of the time, which is quieter and uses less power, and it speeds up when the fridge needs to cool down.
To do that it needs a control board, called the inverter board, that converts the power and drives the compressor. The board is the weak point, because it dislikes surges and heat. When a board fails, the compressor does not start, even though the compressor itself may be fine.
That is why we test the board, the wiring and the compressor separately. A board can sometimes be repaired and sometimes needs replacing with a matching part. A voltage guard and a clean condenser are the best protection for an inverter fridge.
Fridges and freezers we work on.
Fridge trouble in Ruaka?
Call or WhatsApp with what the fridge is doing and a photo of the model sticker. We tell you when a technician can come.