Fridge repair in Kilimani.
Fridge and freezer repair at your home in Kilimani, Nairobi, including Kileleshwa, Hurlingham, Yaya and Valley Arcade. Price agreed before any work starts.
Homes, shops and offices.
We repair home fridges, chest freezers and shop coolers in Kilimani and nearby Kileleshwa and Hurlingham. Tell us what the fridge is doing and where you are, and we give you the earliest time a technician can reach you.
Most jobs are done in one visit. If a part has to be ordered, we tell you the price and how long it takes before we leave.
Homes and businesses we visit.
Kilimani is dense with apartments, serviced flats and small offices. Many households have a compact fridge in a narrow kitchen, used heavily by several people. Doors are opened often, so seals and fans wear sooner than in a quiet household.
Serviced apartments and small guest houses also run more than one fridge, including minibar units. We can look at all of them in one visit.
Kilimani has many flats, serviced apartments and small offices. Fridges in these homes are often used all day with the door opened a lot, so door seals and fans wear sooner. We check the seal and the fan on most visits here.
Our technicians serve Kilimani and nearby Kileleshwa, Hurlingham, Yaya and Valley Arcade. Most jobs are finished in one visit, and we agree the price before the technician starts work.
What goes wrong here.
Door seal wear from heavy use
A seal that no longer grips lets in warm damp air. That brings frost and makes the fridge run longer. Replacing the seal and checking the door alignment fixes it.
Fan that is slowing down
The fan that moves cold air from the freezer into the fridge wears out over time. When it slows or stops, the fridge side warms while the freezer stays cold.
Ice build-up at the back
Ice on the back wall of the freezer means the defrost system is not clearing frost. The heater, sensor or timer is the usual cause.
Minibar and small fridge faults
Small absorption and compressor minibars have their own thermostats and fans. We check the cooling method first so the right repair is chosen.
Care for Kilimani kitchens.
In a flat with limited ventilation, leave a hand-width gap behind the fridge and clean the coil every few months. Keep the fridge away from the cooker if the layout allows.
Most Kilimani fridge faults are fans, seals and sensors, which repair well. Where a small fridge has a failed sealed system and costs more to fix than to replace, we say so.
What we fix.
Brand-specific repair in Kilimani.
If you know the brand, go straight to the page for that brand in Kilimani. The usual faults and how we fix each one, written for your model.
How a Kilimani visit works.
Tell us what is wrong
Call or WhatsApp with what the fridge is doing and a photo of the model sticker inside.
We come to you
A technician visits your home or business and finds the fault.
You approve the price
You get the full price before any work starts. Nothing is done without your OK.
Cold again
We repair it, test the temperature and show you what was fixed.
Good to know about your fridge.
What happens on a visit
You call or WhatsApp us with what the fridge is doing and a photo of the model sticker. We tell you when a technician can come and how the visit fee works. The technician arrives, listens to the fridge, measures the temperature in both sections and checks the obvious causes in order.
When the fault is found, you are told what it is, shown the worn part where possible and given the full price for parts and labour before anything is changed. Nothing is done without your agreement. If a part has to be ordered, we tell you how long it will take.
After the repair, the fridge is left running and checked to confirm it is pulling down to temperature. Before we leave, we explain what failed and how to avoid it next time. If the fridge is not worth repairing, we say so, and we can collect an old fridge for responsible recycling.
How a fridge actually keeps things cold
A fridge does not make cold. It moves heat. Inside the sealed pipework there is a refrigerant gas. The compressor squeezes the gas, which makes it hot, and the hot gas flows through the coil at the back or underneath, called the condenser, where it gives its heat to the room. The gas turns to a liquid, passes through a very thin tube that drops its pressure, and arrives in the cold coil inside the fridge, the evaporator, where it turns back to a gas and soaks up heat from the food. Then it returns to the compressor and the cycle repeats.
That is why the back of a fridge feels warm and why a fridge squeezed into a cabinet struggles. If the heat cannot leave, the cycle slows and the compressor runs for longer. It is also why gas does not get used up: it travels round in a closed loop. When a fridge is low on gas there is a leak, and the leak has to be found and sealed first.
In a no-frost fridge a fan blows air over the evaporator and into the compartments, and a small heater melts the frost off the coil a few times a day. Most cooling faults come from these supporting parts, the fan, the heater, the sensor and the board, long before the compressor itself fails.
Reading the rating plate inside your fridge
Almost every fridge has a sticker or metal plate inside, usually on a side wall or at the back of the fridge compartment. It tells a technician almost everything: the brand, the model number, the voltage and frequency, the type of gas the fridge uses and how much of it, and often the manufacturing date.
Take a clear photo of that plate before you call. With the model number we can check which thermostat, seal, fan or board fits, which saves time on the visit. The gas type matters too. Modern fridges often use R600a, a flammable gas used in small amounts, while older ones commonly use R134a. The two are not interchangeable, and a fridge must always be charged with the gas printed on its own plate.
If you cannot find the plate, look for a sticker behind the vegetable drawers, on the inside of the door frame or on the back of the cabinet. Send us whatever you can find and the brand, and we will help you identify the model.
Protecting a fridge from power cuts and surges
Power cuts and surges are hard on fridges. When the supply returns it can arrive with a spike that damages the control board or the parts that start the compressor. Inverter fridges are the most sensitive, because a board sits between the plug and the compressor.
A good voltage guard, also called a fridge guard, delays the power coming back for a few minutes and cuts it if the voltage is too high or too low. It costs far less than a board repair. Choose one rated for the fridge, plug the fridge into it directly and avoid sharing the socket with a heater or an iron.
After any outage, wait a few minutes before switching the fridge on if you do not have a guard. Keep the door closed during the cut. A full fridge holds its cold for several hours if it is not opened, and a full freezer holds it for longer. Do not keep switching the fridge off and on at the wall; it puts strain on the compressor.
Food safety when a fridge stops cooling
Bacteria multiply quickly above about five degrees. If the fridge side is warm, move milk, meat, fish and cooked food to the freezer or a cool box with ice, and keep the door closed as much as you can. If the freezer is still frozen, do not open it more than you need to.
As a rule of thumb, fresh meat, fish, dairy and cooked leftovers should not stay in a warm fridge for more than a few hours. Food that has thawed and warmed should not be refrozen if it has been warm for long. When in doubt, throw it out: a repair is cheaper than being ill.
Medicines that need refrigeration should be moved to a cool box and kept as cold as the label asks. If you are not sure whether something is still safe, check the instructions on the packaging or ask a pharmacist.
Fridges and freezers we work on.
Fridge trouble in Kilimani?
Call or WhatsApp with what the fridge is doing and a photo of the model sticker. We tell you when a technician can come.